Building mixes for swimming pools

put tile on a well-dried concrete, which is glued with special glue, and glue for pools must have good flexibility, so that later could help you keep a lot of pressure.

Here the main thing - remember the rule - tiles for swimming pools is set at greater than usual distance. This is necessary to pool wall to withstand water pressure. Otherwise, tiles will be covered with microcracks, which will seep through the moisture, which will lead to its rapid damage.

Clay pools manufactured in the cement - sand-based with the addition of high quality polymers. This polymer additives impart special adhesive strength and stability.

Tile Adhesives for swimming pools have high moisture and frost, calmly apply it in basins, where there is a big load. They are divided into adhesives, sealants, waterproofing materials, grout for joints, as well as auxiliary chemical materials.

Company DIYcentre offers a glutinous mixture for pools of production MAPEI .

Tile Adhesives for pools of MAPEI distinguished by reliability and flexibility in the application of different materials.

GRANIRAPID - quick-setting adhesive for ceramic tile , natural and artificial stone. This two-component adhesive containing silica sand and artificial rubber. GRANIRAPID has a unique short setting time, faced with the help of the surface already after three hours ready for use. Complete seizure occurs after 24 hours. Clay virtually no shrinkage, and its high binding properties allow the use of the most difficult footing. GRANIRAPID is resistant to mechanical shock, vibration, temperature and humidity. It can be used for internal and external cladding with ceramic tiles of all kinds, glass and ceramic mosaic floor tiles, natural and artificial stone. The high strength and quick setting make GRANIRAPID indispensable in case of an emergency facing the room.

KERABOND - a cement based adhesive for ceramic tiles and insulation materials . Suitable for internal and external works with ceramic tiles and mosaics of all sizes. Also suitable for spot bonding of insulating materials such as polyurethane foam, polystyrene foam, mineral wool, and other Papercrete. KERABOND consists of cement, graded sand, synthetic resins and special additives. KERABOND has a high adhesive ability, it can be used on vertical surfaces, even in cases of heavy tiles. Adhesive composition hardens without noticeable shrinkage after setting, has high strength and water resistance. KERABOND perfectly adheres to all major construction materials and is not affected by weather conditions.

KERALASTIC - polyurethane adhesive, which has waterproofing properties . Suitable for bonding with simultaneous waterproofing ceramic tile, natural stone and mosaics on the basis of concrete, wood, metal, PVC, gypsum and other building materials. Can be used for lining large format tiles are larger than 300 x 300 cm 

KERALASTIC - Two-component adhesive mixture based on polyurethane elastomer containing a special hardener, developed in the laboratory MAPEI . After curing KERALASTIC turns into an elastic membrane with a high adhesion to ceramic tiles and other materials, which has a high moisture resistance and resistance to aging. KERALASTIC can be applied to horizontal and vertical surfaces.

KERACRETE - synthetic rubber latex for adhesives based on cement. KERACRETE is a unique component, which when mixed with Portland cement and sand gives a solution with the highest adhesion and good elasticity. When clutch with all kinds of complicated foundations he shows excellent performance on the mechanical impact and shock resistant. The composition is resistant to temperature differences, is not subject to aging and the effects of liquid chemical reagents. KERACRETE used to work on internal and external cladding with ceramic tiles of any kind. The composition is perfect for bonding steklomozaiki, ceramic and stone-absorbent tiles. KERACRETE used as an additive to cement mortar, when they should be applied to thin materials.

IDROSTOP MASTIC - a special adhesive composition for Installation hydrophilic profile IDROSTOP . IDROSTOP - hydrophilic elastic sealing profile working connections . Due to its chemical composition IDROSTOP in contact with water expands and creates a barrier against water pressure. Profile IDROSTOP used if necessary to create a watertight connection between the different materials. IDROSTOP MASTIC is a paste, easily placed in a horizontal or vertical surface, which hardens under exposure to moisture, forming an elastic layer. IDROSTOP MASTIC excellent adhesion to concrete, steel, PVC and other construction materials.